智慧彩票预测APP

当前位置:智慧彩票预测APP>资讯>贴完膜后我们怎么检查贴的膜是否合格?

贴完膜后我们怎么检查贴的膜是否合格?

2019-05-17 11:40:08 来源:http://www.hhgted.com

1.资料能否正确。
1. Is the data correct?
2.前挡风玻璃折痕不超越1个(包括一个),位置普通在边角部(离边不超越10CM);后挡风玻璃折痕不超越一个(包括一个);位置普通在边角部(离边不超越2CM),侧面折痕不超越一个(包括一个)在雨刮有效范围内不充许有折痕。坐在驾驶位,透过前挡看车外的景物不存在含糊、色差现象。
2. Front windshield creases Do not exceed one (including one), usually located in the corner (not exceeding 10CM from the edge); rear windshield creases Do not exceed one (including one); position is generally in the corner (not exceeding 2CM from the edge), and side creases Do not exceed one (including one) and are not allowed to be filled with creases within the effective range of the wiper. In the driver's seat, there is no ambiguity and color difference in the view outside the car through the front gear.
3.一切贴膜后的玻璃不能有水泡,水必需刮洁净(从玻璃的左右两侧分别察看,能够看得很分明)。
3. No blisters can be found in all the glass coated with film, and the water must be scraped clean (from the left and right sides of the glass, it can be seen clearly).
汽车贴膜验收规范 汽车膜怎样贴才算合格
Specification for acceptance of automobile film
4.侧窗上端的膜裁切平直,侧窗玻璃升到顶部不能漏光;侧窗玻璃两边不能漏光(膜在胶条以外;有光线透过为漏光);副窗玻璃边缘充许漏光,但最大间隔不超越1MM。
济南xpel授权旗舰店
4. The film at the upper end of the side window is cut straight, and the side window can not leak light when it rises to the top; the two sides of the side window can not leak light (the film is outside the rubber strip; there is light passing through it); the edge of the auxiliary window glass is allowed to leak light, but the maximum interval is not more than 1MM.
5.贴前、后挡时,膜离玻璃边缘黑色陶瓷点的最大间隔正负不超越2MM;
5. The maximum distance between the film and the black ceramic dots on the edge of the glass does not exceed 2MM in front and back shielding.
6.贴膜处玻璃不能有明显的划痕。
6. There should be no obvious scratches on the glass.
7.侧窗角条不能有新划痕。
7. There should be no new scratches on the corner bars of side windows.
8.离车1米查看满载玻璃贴膜后部分范围10CM内,尘点数不能超越10个。
8. Within 10CM of the full-loaded glass film after 1 metre from the vehicle, the dust number can not exceed 10.
9.个别金属膜因有多层金属层,在烤膜的时分可能会呈现金属虚印,但位置普通在边部(离边15CM内)中间位置不允许呈现。
9. Individual metal films may show metal false impression when baking because of multi-layer metal layers, but the position is generally not allowed in the middle of the edge (15 CM away from the edge).
10.贴膜是高风险的效劳项目,因技术程度或玻璃的缺陷,存在玻璃决裂可能,在贴膜中或贴膜后24小时内呈现玻璃决裂的现象,该店担任改换。
10. Film-sticking is a high-risk service project. Because of technical level or glass defects, there is a possibility of glass cracking. The phenomenon of glass cracking appears in the film-sticking or within 24 hours after film-sticking, and the shop acts as a replacement.
本文由 济南xpel授权旗舰店整理发布,您是不是对这些内容有所了解了呢?更多的内容请点击:http://www.hhgted.com我们会有更多精彩内容等你查看。
This article is organized and published by the authorized flagship store of Jinan xpel. Do you know something about these contents? For more information, please click: http://www.hhgted.com. We will have more wonderful content for you to see.